← Back to Contents
2 Maintenance and Service / 2.1 Vehicle Inspection | PDF pages 55-56
2.1 Vehicle Inspection
2.1 Vehicle Inspection
2.1.1 Description and Operation
2.1.1.1 Inspections Items During Vehicle Operation
Operation of Horn
cold tires and the spare tires for vehicles equipped with spare
tires, and maintain the recommended pressure indicated on
The horn shall be pressed occasionally to ensure that the
the tire label.
horn is working properly, and all button positions shall be
checked.
Maintenance interval: Check at least once a week, and
increase the frequency of inspection according to the actual
Operation of Braking System
situation.
When braking, pay attention to abnormal noises from the
2.1.1.4 Inspection Items At Least Once a Month
braking system, increased brake pedal stroke, or repetitive
Month
braking deviations. In addition, if the brake warning lamp is
illuminated or flashing, it indicates that certain parts of the
Air Pressure Inspection of Tires and Wheels
braking system may be failed.
Check the tires for abnormal wear or damage and the wheels
Alignment of Tires and Vehicle
for damage, check the pressure of cold tires and the spare
tires for vehicles equipped with spare tires, and maintain the
Pay attention to vibrations of steering wheel or seats when
recommended pressure indicated on the tire label.
driving at normal road speeds. If the steering wheel or seats
vibrate, it indicates that a wheel shall be balanced. In addition,
Operation of Lamps
if off-tracking is found of the vehicle running on a straight road,
Check the operations of license plate lamps,headlamps
it indicates that the tire pressure shall be adjusted or the
(including high and low beams), tail lamps,stop lamps, turn
wheel alignment should be performed.
signal lamps, backup lamps, and hazard warning lamps.
Operation of Steering System
Inspection of Oil Leakage
Pay attention to changes in steering operations. If it is difficult
After the vehicle has been parked for a certain period of time,
to turn the steering wheel or there is a larger free travel, or
check whether there is water, oil or other liquids on the ground
abnormal sounds are heard when turning or parking,
under the vehicle. It is normal for the A/C system to drip after
inspection shall be carried out. It is necessary to occasionally
use. If leakage of other liquids is found, investigate the cause
observe the light pattern of the headlamp in the event of
and troubleshoot immediately.
focusing, and make adjustment if the beam focusing of the
2.1.1.5 Inspection Items At Least Twice a Year
headlamp is incorrect.
2.1.1.2 Inspections Items During Refueling
Lubrication of Door and Window Sealing Strip
If a system (except for the windshield washer) loses fuel, it
Apply a thin layer of silicone-based grease to the sealing strip
indicates that the system fails, and it shall be inspected and
with a clean rag.
repaired immediately.
2.1.1.6 Inspection Items At Least Once a Year
Inspection of Coolant Level and Condition
Condition and Operation of Seat Belt
Check the coolant level in the expansion tank, add coolant if
Check the harness system, including braided straps, latches,
necessary, check the coolant, and replace dirty coolant.
lock plates, retractors, guide rings and fixtures.
Inspection of Washer Fluid Level
Body Lubrication and Maintenance
Check the washer fluid level in the tank and add washer fluid if
Lubricate all door hinges and hydraulic locks.
necessary.
Cooling System
2.1.1.3 Inspection Items At Least Once a Week
Week
Check the coolant. If the coolant is too dirty or rusty, you
should drain and flush the cooling system and refill with new
Tyre Inspection
coolant. Maintain proper coolant concentration to ensure
proper freezing, boiling and corrosion performances and
Maintenance instructions: Check the tires for abnormal wear
operating temperatures. Check the hoses and replace hoses
or damage and the wheels for damage, check the pressure of
that are cracked, swollen, or aged. Tighten the clamps, and
clean the outside of the radiator and the A/C system
condenser as well as the filler cap. Carry out pressure test the
cooling system to ensure that the system is functioning
properly.